Product Description

With the punch tool PP 37-00, 2 x 2 round lateral eyes are punched in disposable medical catheter tubes.

The punching tools are mounted in the punch press and powered by 2 pneumatic cylinders. These are operated by a foot pedal. An eye pattern of 2 x 2 round lateral eyes is punched in each operation. The 2 eyes are punched 90° opposite for each other. Additional eyes are punched by forwarding the tube to the next eye punch press position. The eye position can be read on the ruler. PP 37-00 CH-8 cross punch tool

Production capacity:
The production capacity is between 800-1.400 units per hour. Depending on the CH size of the tube and the experience of the operator.

Tube specifications:
Tube Diameter: CH/Fr 4-35. (One punching tool is used for each CH size/eye pattern)
Tube Material: Most thermoplastics.
Tube Length: Infinite.

Installation:
Required Space: Length app. 250mm, width 250mm, height 250mm.
Compressed Air: 6-8 bars of cleaned and dried air.

Environment:
It is recommended to operate the machine in a clean environment

Product Description

The punching tool PP 41-00 is used for side cutting lateral eyes in disposable medical catheters.

This is done to prevent the open catheters. This is done to prevent the open catheter tip to stick to the mucous membrane, or with the closed tip catheter to allow drainage function of the catheter. The PP 41-00 is pneumatically driven; an air cylinder activates the two punching needles. The air cylinder is controlled with a foot pedal. When the foot pedal is pressed, the air cylinder presses the needles down and pulls them back up when the pedal is released. PT CH-XX Punch tool PP 41-00 Punch press

Production capacity:
The production capacity is between 1.200-1.400 units per hour. Depending on the CH size of the tube and the experience of the operator.

Tube specifications:
Tube Diameter: CH/Fr 3-35. (One punching tool is used for each CH size/eye pattern)
Tube Material: Most thermoplastics.
Tube Length: Infinite.

Installation:
Required Space: Length app. 180mm, width 150mm, height 250mm.
Compressed Air: 8 bars of cleaned and dried air.

Environment:
It is recommended to operate the machine in a clean environment.

Product Description

With the punching press PP 51-00, 2 top cut lateral eyes are punched in disposable medical catheters.

This is done to prevent the open catheter tip to stick to the mucous membrane, or on the closed tip catheter to allow the drainage function of the catheter. Due to the punch design, the eyes can be punched after the tip forming. The eye is punched from the top, which leaves a small mark on the inside of the tube. This mark is a quality sign, conforming that the punch excess has been removed from tube. The punching tools are mounted in a pneumatic driven punch press and are operated by a foot pedal. An electrical switch system can be supplied as an option. To remove the punch excess, the punching tool has to be connected to both a filter housing and a vacuum pump.

Production capacity:
The production capacity is between 1.000-1.200 units per hour. Depending on the CH size of the tube and the experience of the operator.

Tube specifications:
Tube Diameter: CH/Fr 5-35 (one punching tool is used for each CH size and eye pattern).
Tube Material: Most thermoplastics.
Tube Length: Infinite.

Installation:
Space: Length app. 400m, width 170mm, height 140mm.
Compressed Air: 6 bars of cleaned and dried air.

Environment:
It is recommended to operate the machine in a clean environment.

Product Description

With the vacuum pump, production waste such as punch or drill waste can be sucked away from the connected production equipment.

The production equipment and the vacuum pump are connected via a vacuum hose. The punch and drill waste is sucked away and trapped into a filter housing, located on the rear side of the vacuum pump housing. The Vacuum pump is located inside the Stainless Steel housing, the flow and pressure specification of the vacuum pump is chosen depending on the connected production equipment. Depending of the production and waste type, the filter must be cleaned regularly. To clean the filter, the vacuum pump must be turned off, and the filter housing can be screwed of and cleaned.

The power switch is located on the front of the Vacuum pump housing. Depending on control
system on the connected production equipment, the vacuum pump is turned on manually or will be
turned on automatically with your production equipment.

Installation
Space requirement for the vacuum pump: Length app. 600mm, width 300mm, height 300mm.
The machine is connected to 1x230V AC 50-60Hz 10A

Environment
The vacuum pump is recommended to be operated in a clean room environment